■ 迷你的截面积与机箱周围无线材

■ 主机板旋转90度的烟囱式散热机构

■ 支持任何长度显示卡

■ 支援高塔型CPU散热器

■ 强迫式背位理线设计

■ 热插拔硬盘机构,符合便捷的数据储存需求

■ 硬盘架于背面,被动散热超静音



型号 SST-FT03B (黑)
SST-FT03S (银)
SST-FT03T (钛)
材质 铝外罩, 铁机身
主机板 Micro-ATX, Mini-DTX, Mini-ITX
磁盘架 外露 吸入式薄型光驱 x 1
隐藏 3.5" x 3 * , 2.5" x1
散热系统 --
侧边 --
顶部 1 x 120mm 出风风扇, 1200rpm, 22dBA
1x 92/80mm Option
底部 2X120mm进气风扇 1200rpm 22dBA
后方风扇向下兼容至80mm *2
内部 --
水冷排支援 前方 N/A
背部 N/A
上方 120mm x 1
底部 N/A
扩展槽 4
前置 I/O USB 3.0 x 2 (向下兼容于USB 2.0)
audio x 1
MIC x 1
电源 标准 PS2(ATX)
扩充卡 可相容于13.77" 长扩充卡 (349mm), 宽度-6.77" (171mm)
处理器散热器限高 167mm
电源供应器深度限制 选配 最长180mm
净重 6.7kg
尺寸 235mm(W)x487mm(H)x284mm(D), 32.5 公升


  • 文件下载
  • 推荐产品
  • 产品评测
  • 问与答

描述 版本 大小 下载
FT03 Manual v2.0 6,076 KB
FT03 高分辨率照片 16,752 KB
FT03 eDM (CN-FT03-EDM.pdf)   450 KB

PP05-E 短版超柔软扁平电缆电源线材 更多...
FN81 Add FN81 for additional cooling in available 80mm fan slots 更多...
FQ81 80mm ultra-quiet PWM fan 更多...
ST75F-PT 世上最小80PLUS白金牌全模块ATX电源供应器 更多...
According to tests we’ve done internally, a CPU with TDP rating of 130W (such as Intel Core i7), can run with a fanless tower-style heatsink inside the FT03. However, this does not account for overclocking and performance will vary depending on the efficiency of the heatsink used. We suggest that you try at your own risk.
When the hard drives are installed, they are so close to the aluminum side panel that passive heat conduction does occur to help reduce drive temperature. For the hard drive installed in the hot-swappable bay, an aluminum block pre-attached to the side panel will also help to provide heat conduction for cooling duty.
The FT03 was designed to have the smallest footprint possible and to be aesthetically pleasing so a slim optical drive with slot loading is the best choice to achieve this objective.
Yes, the exhaust from the power supply will have a small effect on overall case temperature. This is unavoidable due to FT03’s small footprint design. However, our internal testing has shown that if a high efficiency power supply is used (such as SilverStone’s 80 PLUS Silver certified Strider Plus series), the exhaust temperature will likely stay below 35 degrees Celsius and have minimum effect on overall case cooling performance.
One of FT03’s design parameters was to eliminate all cable connections on all four sides of the case. As most power cords are connected closer to the floor and usually below case height, we moved the power cord connector to the bottom of the case for more elegant integration.
Extensive testing was conducted during FT03’s development to determine the optimal height of the case stand for air intake so there is no benefit to increase the height any further. The bottom of FT03 has an integrated fan filter that can effectively cut down dust intake into the case so as long as the filter is cleaned on a regular basis, there is no need to worry about dust or cooling performance.
Yes you can, FT03’s rear and right panel have no ventilation holes or other uses so we actually recommend users to place their FT03 into a corner to further take advantage of its incredibly short footprint.
There are two main types of heat pipes used in popular aftermarket coolers, they are groove and powder. Groove heat pipes are very susceptible to gravity while powder heat pipes are less so. To achieve best performance in either heat pipe technology, they need to be placed horizontally or have the heat source side located below the other end of the heat pipe. We recommend choosing and installing components with heat pipes carefully by taking into consideration of the following examples:


The orientation of an enthusiast motherboard in a normal ATX case

The orientation of an enthusiast motherboard in the FT03

As the illustrations above show, most enthusiast motherboards with heat pipes will work fine in the FT03, the heat source is located below other parts of the heat pipe.
CPU cooler:
Horizontal style cooler

Good orientation Good orientation Bad orientation

Many CPU coolers can be rotated when installing on motherboards, the illustration here shows a SilverStone NT06-E

VGA cooler

The illustration here shows a VGA cooler that will not work well in the FT03 because the heat source side (touching the GPU) ends up being located higher than the other end.

Most users can install it in the 120mm fan slot above the CPU area.