■ Diseño con dimensiones súper pequeñas sin cables en los cuatro lados

■ Disposición con efecto de apilamiento con montaje de la placa base en ángulo de 90 grados

■ Acepta tarjetas gráficas de cualquier longitud

■ Acepta disipadores para CPU de torre

■ Diseño con enrutamiento de cables

■ Incluye bahía para cambio en caliente, útil para necesidades de almacenamiento rápido

■ Montaje de disco duro en la parte trasera con refrigeración pasiva para menor sonoridad



Modelo No. SST-FT03B (negro)
SST-FT03S (plata)
SST-FT03T (titanio)
Material Carcasa exterior de aluminio, cuerpo de acero, cuerpo de acero
Placa Madre Micro-ATX, Mini-DTX, Mini-ITX
Bahías Externas Dispositivo óptico delgado con ranura de carga
Internas 3.5" x 3 * , 2.5" x1
Refrigeración Frente --
Parte posterior --
Lado --
Tapa 1 x ventilador de salida de 120mm, 1200rpm, 22dBA
1 x 92/80mm zócalos para ventilador (montaje opcional)
Parte inferior 2 x ventilador de entrada de 120mm, 1200rpm, 22dBA
2 x 80mm zócalos para ventilador (montaje opcional)
Interno --
Refrigeración aceptada Frente N/A
Trasera N/A
Tapa 120mm x 1
Parte inferior N/A
Slots de Expansión 4
Puertos USB 3.0 x 2 (Compatible con USB 2.0)
audio x 1
MIC x 1
Fuente de Alimentación PS2 estándar (ATX)
Gráficos Tarjeta Acepta tarjetas gráficas de 13,77" (349mm), restricción de anchura – 6,77" (171mm)
Limitación del disipador de la CPU 167mm
Limitación de Fuente de alimentación de hasta 180mm de profundidad
Peso 6.7kg
Dimensiones 235mm(Ancho)x487mm(Alto)x284mm(Profundo), 32.5 litros


  • Descargas
  • Recomendaciones
  • Reseña del producto
  • P y R

Describe Ver tamaño Descarga
FT03 Manual v2.0 6,076 KB
FT03 High resolution photos 16,752 KB
FT03 eDM (ES-FT03-EDM.pdf)   388 KB

PP05-E Desorden de cables en carcasas y sistemas pequeños significativamente reducido. Más...
FN81 Add FN81 for additional cooling in available 80mm fan slots Más...
FQ81 80mm ultra-quiet PWM fan Más...
ST75F-PT Las fuentes de alimentación 80 PLUS Platinum ATX totalmente modulares más pequeñas del mundo. Más...
According to tests we’ve done internally, a CPU with TDP rating of 130W (such as Intel Core i7), can run with a fanless tower-style heatsink inside the FT03. However, this does not account for overclocking and performance will vary depending on the efficiency of the heatsink used. We suggest that you try at your own risk.
When the hard drives are installed, they are so close to the aluminum side panel that passive heat conduction does occur to help reduce drive temperature. For the hard drive installed in the hot-swappable bay, an aluminum block pre-attached to the side panel will also help to provide heat conduction for cooling duty.
The FT03 was designed to have the smallest footprint possible and to be aesthetically pleasing so a slim optical drive with slot loading is the best choice to achieve this objective.
Yes, the exhaust from the power supply will have a small effect on overall case temperature. This is unavoidable due to FT03’s small footprint design. However, our internal testing has shown that if a high efficiency power supply is used (such as SilverStone’s 80 PLUS Silver certified Strider Plus series), the exhaust temperature will likely stay below 35 degrees Celsius and have minimum effect on overall case cooling performance.
One of FT03’s design parameters was to eliminate all cable connections on all four sides of the case. As most power cords are connected closer to the floor and usually below case height, we moved the power cord connector to the bottom of the case for more elegant integration.
Extensive testing was conducted during FT03’s development to determine the optimal height of the case stand for air intake so there is no benefit to increase the height any further. The bottom of FT03 has an integrated fan filter that can effectively cut down dust intake into the case so as long as the filter is cleaned on a regular basis, there is no need to worry about dust or cooling performance.
Yes you can, FT03’s rear and right panel have no ventilation holes or other uses so we actually recommend users to place their FT03 into a corner to further take advantage of its incredibly short footprint.
There are two main types of heat pipes used in popular aftermarket coolers, they are groove and powder. Groove heat pipes are very susceptible to gravity while powder heat pipes are less so. To achieve best performance in either heat pipe technology, they need to be placed horizontally or have the heat source side located below the other end of the heat pipe. We recommend choosing and installing components with heat pipes carefully by taking into consideration of the following examples:


The orientation of an enthusiast motherboard in a normal ATX case

The orientation of an enthusiast motherboard in the FT03

As the illustrations above show, most enthusiast motherboards with heat pipes will work fine in the FT03, the heat source is located below other parts of the heat pipe.
CPU cooler:
Horizontal style cooler

Good orientation Good orientation Bad orientation

Many CPU coolers can be rotated when installing on motherboards, the illustration here shows a SilverStone NT06-E

VGA cooler

The illustration here shows a VGA cooler that will not work well in the FT03 because the heat source side (touching the GPU) ends up being located higher than the other end.

Most users can install it in the 120mm fan slot above the CPU area.